Sakura COOLING ONLY Manual de usuario Pagina 18

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 20
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 17
Important:
The firing temperatures indicated are target values.
Temperatures may vary from one ceramic furnace
to another and must be adapted accordingly.
Each firing should be cooled down quickly (0 min.).
18
Vacumat 200/250/300
Stand-by
temp.
Retention
time
Time vacuum
ON
Drying
time
Final
temp.
Paste opaque 400°C 920°C 7 8.5 2 10.0
1st Margin 450°C 890°C 8–10 7 1 7.5
2nd Margin 450°C 890°C 8–10 7 1 7.5
1st Dentin 450°C 850°C 5 6.5 2 8.0
2nd Dentin 450°C 845°C 4 6.5 2 8.0
Glaze 450°C 810°C 4 6 1.5 0.0
Correction mass 450°C 780°C 5 5.0 2 6.0
Margin Correction 450°C 780°C 8 5.5 2 7
Heating
rate
Multimat MC II/Mach 2
Preheat
temp.
Retention
time
Firing temp.Preheating Drying
Paste opaque 400°C 5 2 1.0 2.0 920°C 60 max.
1st Margin 450°C 8 2 1.0 1.0 890°C 60 max.
2nd Margin 450°C 8 2 1.0 1.0 890°C 60 max.
1st Dentin 450°C 4 2 1.0 2.0 850°C 60 max.
2nd Dentin 450 °C 3 2 1.0 2.0 845°C 60 max.
Glaze 450°C 4 2 0.0 2.0 810°C 60 ----
Correction mass 450°C 4 2 1.0 2.0 780°C 60 max.
Margin Correction 450°C 8 2 1.0 1.0 780°C 60 max.
Time vacuum
ON
VacuumHeating
rate
Programat x 1
Stand-
by temp.
(°C)
Retention
time
(min.)
Vacuum
level
(%)
Vac.
ON
(°C)
Vac.
OFF
(°C)
Heating r
ate
(°C/min.)
Closing
time
(min.)
Paste opaque 400°C 7:00 60 920°C 1:00 100 400 1° below firing temp.
1st Margin 450°C 8:00–10:00 60 890°C 1:00 100 450 1° below firing temp.
2nd Margin 450 °C 8:00–10:00 60 890°C 1:00 100 450 1° below firing temp
1st Dentin 400°C 5:00 60 850°C 1:00 100 450 1° below firing temp
2nd Dentin 400°C 4:00 60 845 °C 1:00 100 450 1° below firing temp
Glaze 400°C 4:00 60 810 °C 0:30 no no
Correction mass 400°C 4:00 60 780 °C 1:00 100 450 1° below firing temp
Margin Correction 450°C 8:00 60 780°C 1:00 100 450 1° below firing temp
Firing
temp.
(°C)
E956 Gebrauchsanl_Sakura E_19_8_08 19.08.2008 22:10 Uhr Seite 18
Vista de pagina 17
1 2 ... 13 14 15 16 17 18 19 20

Comentarios a estos manuales

Sin comentarios