
Important:
The firing temperatures indicated are target values.
Temperatures may vary from one ceramic furnace
to another and must be adapted accordingly.
Each firing should be cooled down quickly (0 min.).
19
Correction
mass
Glaze2nd
Dentin
1st
Dentin
Paste
opaque
Heramat C
Starting temp. (°C) 400 450 450 450 450
Drying time (min) 6:00 5:00 4:00 4:00 5:00
Preheating time (min) 1:00 1:00 1:00 1:00 1:00
Heating rate (°C/min) 60 60 60 60 60
Final temp. (°C) 920 850 845 810 780
Retention time (min) 2:00 2:00 2:00 1:30 2:00
Tempering temp. (°C) – – – – –
Tempering time (min) – – – – –
Cooling down time (min) – – – – –
Vacuum on (°C) 400 450 450 – 450
Vacuum off (°C) 920 850 845 – 780
Time vacuum ON (min) 1:30 1:30 1:00 1:00 1:00
450
8:00–10:00
8:00–10:00
60
890
1:00
–
–
–
450
890
1:00
450
8:00–10:00
8:00–10:00
60
890
1:00
–
–
–
450
890
1:00
1st
Margin
2nd
Margin
450
8:00
8:00
60
790
2:00
–
–
–
450
780
1:00
Margin
Correction
CergoCompact /
CergoPress
Preheat or starting
emperature: (°C) 400 450 450 450 450
Drying and
preheating time: (min) 7 5 4 4 5
Rate of heat increase: (°C/min) 60 60 60 60 60
Final temperature: (°C) 920 850 845 810 780
Retention time: (min) 2 2 1–2 1–2 2
Vacuum starting temperature: (°C) 400 450 450 – 450
Vacuum final temperature: (°C) 920 850 845 – 780
Correction
mass
Glaze2nd
Dentin
1st
Dentin
Paste
opaque
450
8–10
60
890
1
450
890
450
8–10
60
890
1
450
890
450
8
60
780
2
450
780
1st
Margin
2nd
Margin
Margin
Correction
Austromat M START FINE
1Ó
Ó
2
Vac
Paste opaque 400 3 3 2 9 60 920 2:00 0 0
1st Margin 450 3 4 2 9 60 890 1:00 0 0
2nd Margin 450 3 4 2 9 60 890 1:00 0 0
1st Dentin 450 3 2 2 9 60 850 2:00 0 0
2nd Dentin 450 3 2 1 9 60 845 2:00 0 0
Glaze 450 2 2 1 0 60 810 1:30 0 0
Correction mass 450 2 2 1 9 60 780 2:00 0 0
Margin Correction 450 3 4 2 9 60 780 2:00 0 0
E956 Gebrauchsanl_Sakura E_19_8_08 19.08.2008 22:10 Uhr Seite 19
Comentarios a estos manuales